Delaware DMV CDL General Knowledge Practice Test 1
Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Delaware test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. What does gross vehicle weight mean, as opposed to gross vehicle weight rating?
Show answer
Answer B: The actual weight of the single vehicle plus everything it is carrying
Gross vehicle weight is what the vehicle actually weighs at that moment; the rating is the maximum the manufacturer allows it to weigh.
-
2. What does the working load limit stamped on a chain or strap describe?
Show answer
Answer B: The maximum load the device is rated to hold in normal use
The working load limit is the rated safe capacity for everyday use, deliberately set well below the force that would break the device.
-
3. Since June 23, 2025, how must a Delaware commercial driver provide a medical certificate?
Show answer
Answer D: From a medical examiner listed on the federal National Registry
Delaware requires commercial learner's permit and CDL holders to obtain medical certificates from examiners listed on the National Registry.
-
4. Taking your eyes off the road for about five seconds at highway speed means traveling roughly how far unseen?
Show answer
Answer A: About the length of a football field
At highway speed a five second glance away covers roughly 100 yards, which is far more road than any driver can afford to travel blind.
-
5. Loading heavy freight on top of lighter freight has what effect on the vehicle?
Show answer
Answer B: It raises the center of gravity and makes a rollover more likely
A high center of gravity lets the vehicle tip more easily in curves or during a sudden swerve.
-
6. Why does a heavy vehicle need a much larger gap than a car in order to cross or enter traffic?
Show answer
Answer C: Because it accelerates slowly and needs far more road and time to clear the intersection
Slow acceleration combined with the length of the vehicle means a gap that would feel comfortable in a car is nowhere near enough.
-
7. How far ahead can a driver see with low beams and with high beams?
Show answer
Answer C: About 250 feet with low beams and about 350 to 500 feet with high beams
Low beams reach roughly 250 feet and high beams roughly 350 to 500 feet, and speed at night has to stay inside the distance the lights really show.
-
8. During the vehicle overview, what should the driver look for on the ground under the vehicle?
Show answer
Answer B: Fresh puddles of oil, coolant, grease or fuel
New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.
-
9. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?
Show answer
Answer C: Move weight off the drive axles and onto the trailer axles
Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.
-
10. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?
Show answer
Answer C: The drum is defective and must be repaired before the vehicle is driven
Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.
-
11. You are hauling livestock and the trailer is only partly full. What should be done?
Show answer
Answer A: Use false bulkheads or partitions to keep the animals bunched together
Animals that can move around shift the center of gravity, so a partial load is bunched together with partitions to limit how far the weight can move.
-
12. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
13. You need fuel and the canopy over the pumps is low. What is the safe way to handle the clearance?
Show answer
Answer B: Stop and check the height at the entrance and at the way out before committing
Clearance can differ at the entry, under the canopy and at the exit, and a sloping approach changes the effective height, so both ends have to be checked.
-
14. How many years of commercial driving employment history must a Delaware commercial driver license applicant disclose?
Show answer
Answer D: 10 years
The application must list previous employers for whom the applicant drove commercial vehicles during the years preceding the application, covering a full decade.
-
15. Your speedometer stops working during the pre-trip check. How should it be treated?
Show answer
Answer D: As a defect, because the driver cannot judge and control speed without it
A working speedometer is required equipment, because judging speed by feel in a heavy vehicle is unreliable and speed governs stopping distance.
-
16. How does a load carried high in the trailer affect safe speed through a curve?
Show answer
Answer B: It raises the rollover risk, so the speed must be lower
A high center of gravity lets the vehicle tip long before the tires lose their grip, so height of the load directly limits curve speed.
-
17. Under the federal air brake standard, the low air pressure warning must come on before reservoir pressure drops below what level?
Show answer
Answer A: Before pressure falls below 60 psi
Federal Motor Vehicle Safety Standard 121 requires the warning to operate while service reservoir pressure is still above 60 psi, which leaves enough air to bring the vehicle to a normal stop.
-
18. What is normally required in order to move an over-width or over-length load?
Show answer
Answer B: A special permit along with warning devices such as flags and signs
Oversize movements need a permit plus marking devices, and travel is often limited to certain hours or routes.
-
19. You are not certain that your loaded vehicle will clear a low overpass. What should you do?
Show answer
Answer A: Take another route rather than risk it
There is no safe way to guess at a clearance, and striking a bridge endangers everyone on and under it, so the only correct choice is a different route.
-
20. How should speed and gears be handled when approaching a curve?
Show answer
Answer A: Slow to a safe speed and downshift before entering the curve
Braking and shifting are completed before the curve so the vehicle is settled and can pull gently through it without upsetting the load.
-
21. Why can an empty truck need a longer stopping distance than a loaded one?
Show answer
Answer C: An empty vehicle has less traction, so its wheels lock up more easily
Brakes and tires are designed for a loaded vehicle, and with little weight on the axles the tires grip less and lock sooner.
-
22. What is the most common cause of a front-wheel skid, where the vehicle keeps going straight even though you turn the wheel?
Show answer
Answer B: Driving too fast for the conditions
A front-wheel skid usually comes from too much speed for the traction available; the only cure is to let the vehicle slow down and stop turning or braking so hard.
-
23. On a wet road, a commercial driver should reduce speed by roughly how much?
Show answer
Answer C: By about one third
Cutting speed by roughly a third, for example from 55 to about 35 mph, restores a margin for the traction lost on a wet surface.
-
24. Your axle weights are legal, but the tires on that axle are rated below the weight it is carrying. What controls?
Show answer
Answer B: The lower figure, so the tires may not be loaded beyond their marked rating
You may never exceed the rating marked on a tire, even when the axle limit would allow more, because an overloaded tire builds heat and can fail.
-
25. What do the U-bolts on a leaf spring suspension do?
Show answer
Answer A: They clamp the spring assembly to the axle so it cannot move
U-bolts hold the spring pack tight against the axle, and a loose or broken U-bolt lets the axle slide out of place under load.
-
26. What should you check about the fuel tank during the walkaround?
Show answer
Answer A: That it is securely mounted, the cap is on tight and there are no leaks
A loose tank or a missing cap can spill fuel, and any fuel leak is a fire hazard that makes the vehicle unsafe to drive.
-
27. Which wheel or rim condition must be treated as a defect during the walkaround?
Show answer
Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts
Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.
-
28. The coolant temperature gauge climbs above its normal range on a long grade. What is the correct response?
Show answer
Answer C: Stop when it is safe to do so and find the cause before going on
Rising coolant temperature signals a fault such as a lost belt, a leak or a blocked radiator, and continuing can turn a repair into a destroyed engine.
-
29. What must a written driver vehicle inspection report cover at the end of the day?
Show answer
Answer C: Any defect or deficiency that would affect safety or could cause a mechanical breakdown
The report identifies the vehicle and lists defects that affect safe operation or could lead to a breakdown, so they are repaired before the next trip.
-
30. What must the driver check about the seat belt during the inspection?
Show answer
Answer A: That it is securely mounted, adjusts properly and is not ripped or frayed
A belt only restrains the driver if its anchorage is sound and the webbing is intact, so mounting and condition are both checked.
-
31. Most rollovers of loaded trucks on exit and entrance ramps happen for which reason?
Show answer
Answer B: The ramp was taken faster than the load could tolerate
A posted ramp speed is set for cars, and a loaded trailer with a high center of gravity can roll at a speed a car would take easily.
-
32. After coupling, where should the fifth wheel release handle be?
Show answer
Answer A: In the locked position with the safety latch in place
The handle must be pushed in and latched, because a handle left out means the jaws can open and release the trailer while you are driving.
-
33. What blood alcohol concentration disqualifies the holder of a commercial driver license who is operating a commercial vehicle?
Show answer
Answer D: 0.04 or higher
Commercial drivers are held to 0.04, half the limit that applies to a driver of a passenger car in the same state.
-
34. Why must the downshift be finished before you reach a steep downgrade or a sharp curve rather than during it?
Show answer
Answer D: Because once your speed is too high you may not get into any gear at all
If you wait until speed has built up, the lower gear may refuse to engage and you can be left in neutral with no engine braking at all.
-
35. If an intersection has two lanes marked for left turns, which one should a large vehicle use?
Show answer
Answer D: The right hand of the two turning lanes
The outside turning lane leaves room for the rear of the vehicle to swing without striking a vehicle in the adjacent lane.
-
36. You are taking a tightly curved highway exit ramp in a long combination. Where should the tractor be placed within the lane?
Show answer
Answer D: Toward the outside of the curve, leaving room for the trailer to track inside
Because the trailer wheels cut to the inside of the curve, the tractor has to be kept out toward the outer edge so the trailer does not drop a wheel off the inside edge.
-
37. What happens to braking performance if oil or grease reaches a brake lining?
Show answer
Answer B: That brake loses much of its effect and the vehicle can pull to one side
A contaminated lining cannot grip the drum, so that wheel contributes little braking and the vehicle pulls toward the side that is still working.
-
38. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
39. What must be checked about the cargo doors and any tarpaulin before a trip?
Show answer
Answer B: That the doors are closed and latched and that any tarp is tied down securely
An unlatched door or a loose tarp can swing open or tear free at speed, spilling cargo or blocking the view of the traffic behind you.
-
40. Under the federal hours of service rules, how long may a property-carrying driver drive after 10 consecutive hours off duty?
Show answer
Answer D: Up to 11 hours, and only within a 14 hour window that starts when the driver comes on duty
The federal limit is 11 hours of driving after 10 consecutive hours off duty, and all of that driving has to fall inside a 14 hour window.
-
41. You find one lug nut missing from a wheel that has ten studs. What should you do?
Show answer
Answer C: Treat it as a defect and have it repaired before the vehicle is driven
Every missing fastener loads the others more heavily, and wheel separations usually begin with one nut that nobody replaced.
-
42. Why do worn tires lose grip so quickly on a wet road?
Show answer
Answer D: Shallow tread cannot move water out from under the tire
The grooves in a tire exist to channel water away so the rubber can touch the road, and a worn tire has lost that capacity.
-
43. How do you confirm that the coupling is locked before pulling out of the yard?
Show answer
Answer D: By locking the trailer brakes and pulling gently forward against them
The tug test loads the coupling in the direction that would pull it apart, so if the jaws are not closed on the kingpin you find out at walking pace.
-
44. What is the correct way to test the parking brake before a trip?
Show answer
Answer C: With the parking brake set, put the vehicle in a low gear and gently try to move forward
A parking brake that holds against a gentle pull in low gear is working; if the vehicle moves, the brake needs adjustment or repair.
-
45. Which situations call for a mirror check in a commercial vehicle?
Show answer
Answer A: Every lane change, turn, merge and tight maneuver
Mirrors must be checked regularly and always before, during and after any movement that changes the path of the vehicle.
-
46. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.
-
47. For an unblocked article longer than 10 feet, the minimum is two tiedowns plus how many more?
Show answer
Answer B: One more for every additional 10 feet of length or any part of 10 feet
Past the first 10 feet, one more tiedown is added for each additional 10 feet of length or any fraction of that distance.
-
48. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
49. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
50. For how long may a Delaware commercial learner permit be valid?
Show answer
Answer C: 1 year
Delaware issues the commercial learner permit for a period that does not exceed one year, and only one renewal or re-issuance is allowed within a one-year period.